Linear Gate Motor Replacement Nationwide

Linear Gate Motor Replacement: The Orlando Owner’s Guide

A Linear gate motor replacement in Orlando typically runs $650 to $1,450 installed, depending on the model and whether the arm, receiver, or full operator needs swapping. We stock Linear-compatible operators and parts on our trucks, and most replacements are completed the same visit. The giveaway is usually obvious: the gate stops moving, the motor hums without turning, or the operator works intermittently after a storm.

Call (321) 465-7089

Owners usually catch it one of three ways. The remote stops working but the keypad still opens the gate. The gate starts and stalls halfway, then needs a manual push. Or the motor housing is hot to the touch and the arm doesn’t engage at all. In Orlando, the humidity accelerates the failure points we describe below, particularly on arms exposed to afternoon sun and the daily rain cycle from May through October.

Key takeaways:

• Installed Linear motor replacement in Orlando: $650 – $1,450
• We carry Linear-compatible operators and arms on the truck
• Same-visit replacement for most single-family swing and slide gates
• Written price before we touch anything, backed by our 365-Day Done Right Promise

Which Linear Models This Applies To

We replace motors and internals across the Linear swing gate and slide gate lines most common in Orlando homes: the Linear LRA actuator series, the SLR slide operator line, and the older APeX and MegaCode systems still running in neighborhoods like Conway, College Park, and Baldwin Park. If your gate has a separate control board next to the motor, you’re likely on an LRA or SLR. If the operator is one sealed box with the receiver built in, it’s probably an APeX or a newer Linear-branded swing arm.

The compatibility gotcha specific to Linear: the board and the motor are matched by revision, not just series. A motor from an LRA-S swing arm won’t simply bolt onto every LRA housing. We check the part number on the actuator label or the operator’s data plate before quoting anything. If the label is sun-blasted off, we measure the arm stroke and the mounting bolt spread. That’s saved more than a few Orlando customers from paying for a part that fits the gate but not the board.

As for parts themselves, genuine Linear OEM is the right call for the control board and receiver. For arms and limit switches, quality aftermarket equivalents from US suppliers hold up just as well and save real money. We’ll show you both prices and let you decide. Warden Gate Repair Orlando is an independent service provider, not affiliated with Linear, and we also stock parts for LiftMaster, Mighty Mule, and Ghost Controls systems.

Signs Your Linear Gate Motor Replacement Is Failing

• Gate hums but won’t move. The motor is getting power but the gear train or arm coupling has stripped. This is the most common failure we replace, and it only gets worse if you keep pressing the remote.
• Intermittent operation after rain. Water has found its way into the motor housing or limit switch. In Orlando’s daily summer storms, a worn seal turns a small leak into a dead motor within a few weeks.
• Gate stops mid-travel and reverses. The Linear’s obstruction sensing is tripping, or the limit switch is worn and sending a false stop signal. If adjusting the sensitivity doesn’t clear it, the motor itself is usually on its way out.
• Manual release won’t re-engage. The release mechanism inside the operator is corroded or bent. This is common on gates that get manually operated often, like pool gates and driveway gates on short, frequent cycles.
• Remote and keypad both dead but the motor is warm. The control board has failed, and in many Linear models the board and motor are replaced as a matched pair. We diagnose this before ordering anything so you don’t pay twice.

Replacement Cost & What’s Included

Here’s the honest pricing picture for Orlando. A Linear swing arm replacement (actuator only) runs $350 – $750 installed. A full Linear operator replacement, including the motor, board, receiver, and arm, runs $900 – $1,450 for single-family gates. Slide gate operators land on the higher end because the motor drives a chain or rack and takes longer to align properly.

Every Warden Gate Repair Orlando quote includes the part, labor, removal of the old unit, alignment, and a full cycle test. The written price you get before we start is the price you pay, no line-item surprises at the end. If the replacement isn’t right, the 365-Day Done Right Promise kicks in: we come back and make it right, free.

Call (321) 465-7089 for an exact quote. Estimates are free, and you’ll know the price before anything gets unbolted.

DIY or Call Us?

You can safely check a few things yourself. Confirm the gate has power. Check the breaker and the GFCI outlet the operator plugs into. Look for obvious water intrusion or ants inside the housing. Clear debris from the track or hinges. But the moment you need to open the operator housing and touch wiring, capacitors, or the arm’s tension, stop.

Linear gate motors run on line voltage, and the capacitor inside an older unit holds a charge even when unplugged. We also see Orlando homeowners strip the gear train trying to force a seized motor free, turning a $400 arm replacement into a $1,200 full operator job. If the gate isn’t moving and you’ve ruled out power, call (321) 465-7089. We’ll bring the part, the meter, and a written price before any work starts.

FAQs